Vehicles
Sections
130 not categorized PORSCHE 944S A ARM BUSHINGSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 356 1960-65 (includes uncategorized and accessory items) FVD33150005 Restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm cannot compensate enough when lowering your Porsche, leaving you with as much as ½ inch of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration. Sold in pairs. 1 necessary per car.
$764.50
Make a selection FVD33150040 Replace worn-out original rear sub frame (side panel) bushings and return your car to its original ride quality with this cost effective alternative. This bushing is made in Germany. It is crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value core. This is a front and rear bushing for one sub frame. 2 are necessary per car. If you are looking for a sportier upgrade we suggest our clubsport sub frame bushing set, part # FVD33150040r. We also sell complete sub frames with the bushings installed, part # FVD331993001.
$418.00
Make a selection FVD33300902AT Send us your original spring plate and we will have it reconditioned for you. The reconditioning process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and media blast the part. Once fully prepared, we install new rs spec. (85 shore) rubber bushings/bearings. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Then we seal the spring plate with a corrosion resistant plating. Sold individually. 2 necessary per car. Please note: this only fits cars with the g50 transmission.
$261.80
Make a selection FVD205996003VAG These bushings are made for h&r front sway bars with 25 mm diameters. They are a direct replacement for our part # . These will also work on any bar with a 25-mm diameter. If you would also like to replace the rear, please use part # FVD205996003hag sold as a front set. 1 set needed per car.
$58.30
Make a selection FVD33300909ATK This non-adjustable rear spring plate is remanufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. New rs spec. (85 shore) rubber bushings are installed to make this a direct bolt on. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Features: includes new rs spec. (85 shore) rubber bushings made in Germany sold individually. 2 necessary per car. This part is a remanufactured part. Send us your original and we will have it remanufactured for you. We do not offer a core exchange on this part. Each is remanufactured in Germany, so the lead times can vary.
$342.10
Make a selection FVD33391101SET These bushings are manufactured from higher density, rs specification rubber (85 shore). Rs bushings are more durable than OEM 65 shore, provide more positive suspension location and are still quiet and compliant for street use. This set is a direct replacement for original part # 911 333 009 00 sold as a set. 1 necessary per axle.
$108.90
Make a selection FVD34101702ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection FVD34101702RAT We will send you a reconditioned control arm, kindly send back your old part, or core . The reconditioned control arm has been full inspected, disassembled, degreased and we have properly installed FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. This part is sold on an exchange basis, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and r...(choose a part on the right to read more)
$440.00
Make a selection FVD33394401SET Replace worn-out original spring plate bushings to return your car to its intended ride quality and performance. This is a high-quality OEM 65 shore density bushing set, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. This set is a direct replacement for the rear axle strut bushings from original part # 477 511 201 and 477 511 202 sold as a set. 1 necessary per axle.
$108.90
Make a selection FVD34101802ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection FVD34791130 Enhance steering precision and steering feedback by simply replacing your original tie rods. Turbo tie rods use a spherical inner joint instead of soft rubber bushings. They offer quicker steering response, more sensitivity and more precision. These are standard length we highly recommend them for lowered vehicles with bump steer kits like part # FVD34791100 or FVD347911930 . We also offer turbo tie rods in longer lengths for other applications, check part # FVD34791180r and FVD34791181ry this kit is manufactured in Germany by an OEM supplier, made from high carbon steel and 7075 t6 aluminum. Kit includes: 2 qty. Outer tie rods 2 qty. Inner tie rods 2 qty. Spacing washers 2 qty. Boots 2 qty. Castle nuts 2 qty. ...(choose a part on the right to read more)
$222.24
Make a selection 99737503303LA Sport (85shore)bushing for transmission mount. - reduces the movement of the transmission. - improved the handling characteristics during acceleration and curves note: model 996 Carrera only with tiptronic transmission. 500 km running-in period (light noises).
$141.90
Make a selection FVD424041 Ok, we know you are a driving enthusiast if you are shopping for a short shifter for your manual transmission. Driving enthusiasts appreciate a more direct connection to the car, transmission and road surface. If you are trying to clean up those long shifts and side to side play on the factory shifter you are certainly on the right track with this upgrade. This numeric racing short shift kit uses precision ball bearings on all axis' which produce 35% shorter throws with an almost gated like action. Short gated like throws increase your driving experience by enhancing a more direct, mechanical connection to your car. Once installed you will find joy with every shift and this will easily become one of your favor...(choose a part on the right to read more)
$808.50
Make a selection 150SPB968
$35.20
Make a selection 54610110370
View/Change Diagram
From $108.90
Make a selection 53910117470
View/Change Diagram
From $170.50
Make a selection 54610190155
View/Change Diagram
From $479.60
Make a selection 54610190150
View/Change Diagram
From $479.60
Make a selection 61610013050
View/Change Diagram
$1,156.10
Make a selection 61610013870
View/Change Diagram
From $387.20
Make a selection 61610013850
View/Change Diagram
From $447.60
Make a selection 61610013860
View/Change Diagram
From $412.50
Make a selection 61610013890
General Fitment356 1960-65
From $438.90
Make a selection 61610013885
View/Change Diagram
From $438.90
Make a selection 61610314202SET8
$73.70
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |